Home Automation Kit

QUBINO Z-Wave Plus Din Rail Smart Meter ZMNHTD1

QUBINO Z-Wave Plus Din Rail Smart Meter ZMNHTD1
QUBINO Z-Wave Plus Din Rail Smart Meter ZMNHTD1
QUBINO Z-Wave Plus Din Rail Smart Meter ZMNHTD1
QUBINO Z-Wave Plus Din Rail Smart Meter ZMNHTD1
QUBINO Z-Wave Plus Din Rail Smart Meter ZMNHTD1
QUBINO Z-Wave Plus Din Rail Smart Meter ZMNHTD1

QUBINO Z-Wave Plus Din Rail Smart Meter ZMNHTD1  QUBINO Z-Wave Plus Din Rail Smart Meter ZMNHTD1
QUBINO - Din Rail Smart Meter ZMNHTD1. This device operates at 868.4 mhz Z-Wave frequency.

Please make sure that you have a Z-Wave controller with the same frequency. 868.4 mhz is used in CEPT countries, Europe, the EU, China, Singapore, South Africa, UAE, Qatar, Singapore.

This Z-Wave module is used for energy measurements in single-phase electrical power network till 65 A. Meters measure energy directly in 2-wire networks according to the principle of fast sampling of voltage and current signals.

A built-in microprocessor calculates energy, power and power factor from the measured signals. The module can be controlled through Z-wave network and it acts as repeater in order to improve range and stability of Z-wave network. The module can control electrical devices (switching on/off) with. One BICOM432-40-WM1 Bistable switch (32A) controlled by built in optical (IR) communication port, also found in our store.

One IKA232-20/230 V Contactor (32A) controlled by output on terminal 5, also found in our store. Analyses the overall power consumption of a phase. Installs directly in the electrical cabinet. Integrated 500 series Z-Wave chip (Z-Wave+).

Communication 250% faster compared to standard Z-Wave devices. Consumption of less than 2W.

Operating temperature of -10 to 40C. IR connector for an additional DIN relay. Wired connector for an additional DIN relay. LED pulse for an optional optical counter. Measurement and transmission of the following data: Voltage, Current intensity (I), Active power (in W), Total power consumption (in kWh), Reactive power (in var), Total reactive power (kVarh), Total apparent power (in kVAh), Power factor (PF).

Main terminals (LI, NI, Lo, No). Max torque: 3.5 Nm (PZ2). Optional terminals (1,2,4,5). Max torque: 0.6 Nm.

Type (connection): single phase (1b). Reference current (Iref): 5 A.

Maximum current (Imax): 65 A. Minimum current (Imin): 0.25 A. Voltage (Un): 230 V (±20 %). Power consumption at Un: < 2W. Nominal frequency (fn): 50 and 60 Hz. Active energy and power: Standard EN 62053-21: class 1, Standard EN 50470-3: class B. Reactive energy: -Standard EN 62053-23: class 2.

Optical communication: Type: IR - used to control BICOM432-40-IR. Rated voltage: 230 V (± 20%). Safety: Indoor meter: yes, Degree of pollution: 2, Protection class: II, AC voltage test: 4 kV. Installation Category: 300 Vrms cat.

Multiprotocol (Z-Wave, ZigBee, Bluetooth, Wi-Fi) controller also available in our store. The item "QUBINO Z-Wave Plus Din Rail Smart Meter ZMNHTD1" is in sale since Monday, May 23, 2016.

This item is in the category "Consumer Electronics\Surveillance & Smart Home Electronics\Other Smart Home Electronics". The seller is "igl-ai" and is located in Ljubljana, default. This item can be shipped worldwide.

  • Compatible Technology: Z-Wave
  • Connected Home Protocol: Z-Wave
  • Model: ZMNHTD1
  • Country/Region of Manufacture: Slovenia
  • Smart Home Protocol: Z-Wave
  • MPN: QUB_ZMNHTD1
  • Brand: QUBINO
  • Type: Power Meter


QUBINO Z-Wave Plus Din Rail Smart Meter ZMNHTD1  QUBINO Z-Wave Plus Din Rail Smart Meter ZMNHTD1