Home Automation Kit

Bundle New Z-Wave Door/Window Sensor, Sercomm SW-DWS02N 10 units, Motion PIR

Bundle New Z-Wave Door/Window Sensor, Sercomm SW-DWS02N 10 units, Motion PIR
Bundle New Z-Wave Door/Window Sensor, Sercomm SW-DWS02N 10 units, Motion PIR
Bundle New Z-Wave Door/Window Sensor, Sercomm SW-DWS02N 10 units, Motion PIR
Bundle New Z-Wave Door/Window Sensor, Sercomm SW-DWS02N 10 units, Motion PIR
Bundle New Z-Wave Door/Window Sensor, Sercomm SW-DWS02N 10 units, Motion PIR
Bundle New Z-Wave Door/Window Sensor, Sercomm SW-DWS02N 10 units, Motion PIR

Bundle New Z-Wave Door/Window Sensor, Sercomm SW-DWS02N 10 units, Motion PIR    Bundle New Z-Wave Door/Window Sensor, Sercomm SW-DWS02N 10 units, Motion PIR
Vision Z-Wave Plus Wireless PIR Motion & Temperature Sensor ZP 3102US-5. Built on Passive Infrared Technology (PIR). Adjustable motion sensitivity - perfect for households with pets. May be associated with other Z-Wave devices for advanced home automation scenarios.

Z-Wave Plus with improved 500 chip for faster and safer wireless communication. Z-Wave Signal Frequency: 868.42 MHz. Power: CR123A lithium battery (1).

Range: Up to 30m (100 ft) line of sight. Operating Temperature: -15° - 60° C (5° - 140° F). Installation and Use: Indoor only. Dimensions: 84 x 62 x 50 mm. Package Contents: sensor, adhesive tape, CR123A battery, user manual. SW-DWS02N Door/Window Sensor Installation Guide. Z-Wave Door/Window sensors are designed to secure the perimeter of the residential premise, and provide the. Ability to add various automation services. The Z-Wave Door/Window sensor, which consists of a magnet that. Attaches to a door or window, will communicate door events to the home security system.

Moved away from the sensor, a signal will be sent to the control panel that communicates the changed state to the. Signals can also be used to activate a chime or convenience lighting based on system settings. Magnet: 45 mm x 8 mm x 15 mm (1.77" x 0.31" x 0.59). For Adding in (Inclusion) a network: Put the Z-Wave Interface Controller into. Following its instruction to add SW-DWS02N to your controller.

This Door/Window sensor needs to be included. Pull the exposed plastic tab from the sensor.

The Green LED indicator will be lit for one second to indicate a successful booting. It will blink one time every second while scanning the network (Figure 2). If network is not found after 30 seconds, the sensor will go into sleep mode. To wake the sensor again, you. Need to use magnet or tamper (Figure 3) to trigger a paring process, and then sensor will repeat steps from 3 to.

For Removing from (Exclusion) a network: Put the Z-Wave Interface Controller into. And following its instruction to delete SW-DWS02N to your Z-Wave controller.

Remove device rear cover and pressing the tamper button. Within 2 seconds, green LED indicator. 0.5 second and enter exclusion mode. If remove (exclusion) successful, go auto Adding procedure. Node ID has been remove. Within 2 seconds (Figure 4) and do not release the tamper button in the. Pressed, and the LED will turn ON. After over 3 seconds the Green LED indicator will turn OFF, then go auto Adding procedure. IDs are excluded and all settings will reset to factory default. Device begin auto Adding (Inclusion) mode. Note: Use this procedure only in the event that the primary controller is lost. Please make sure that the sensor and magnet is located less than 0.7 inch from each other. Performance, it is highly recommended to install the Door/Window sensor on the fixed frame and the magnet. On the moving part of the door/window. Place the sensor near the top of the door that close to the opening. This is the mounting location for the sensor. Use the provided double-sided tape on the sensor. Attach the sensor to the door. Press firmly and hold in place. For a few seconds (Figure 5). Secure it with silicone if needed. Use provided double-sided tape on the magnet. Make sure the alignment of both sensor and magnet alignment.

Mark are facing each other (Figure 6). Press firmly and hold in place for a few seconds. Adhesive application surface: Acrylic, Glass. SW-DWS02N can be included and operated in any Z-Wave network with other Z-Wave certified devices.

From other manufacturers and/or other applications. All non-battery operated nodes within the network will. Act as repeaters regardless of vendor to increase reliability of the network. Support grouping identifier = 1. Support one group with 5 nodes.

All triggering report and low voltage report will be sent to the associated nodes. It will be triggering after opening bottom cover. Wake Up No More Information.

Command then will go off or it will. Wait 10 seconds then go off. It will proceed all the commands after sending the. Command to set up the awaking time and send the wake up notification to controller.

User can use command to change the auto wake up from 1 minute to 24 hours, interval increment is 1. Factory default is 120 minutes.

The Green Pairing LED will stay off during the normal operation. The sensor is equipped with a tamper switch. If the cover of sensor is removed, the sensor will send an alarm. Tamper switch event will be ignored when in auto inclusion procedure.

The item "Bundle New Z-Wave Door/Window Sensor, Sercomm SW-DWS02N 10 units, Motion PIR" is in sale since Friday, April 12, 2019. This item is in the category "Consumer Electronics\Surveillance & Smart Home Electronics\Other Smart Home Electronics".

The seller is "z-kekc" and is located in Menlo Park, California. This item can be shipped to United States, Canada, United Kingdom, Denmark, Romania, Slovakia, Bulgaria, Czech republic, Finland, Hungary, Latvia, Lithuania, Malta, Estonia, Australia, Greece, Portugal, Cyprus, Slovenia, Japan, China, Sweden, South Korea, Indonesia, Taiwan, South africa, Thailand, Belgium, France, Hong Kong, Ireland, Netherlands, Poland, Spain, Italy, Germany, Austria, Bahamas, Israel, Mexico, New Zealand, Philippines, Singapore, Switzerland, Norway, Croatia, Brazil, Chile, Colombia, Antigua and barbuda, Aruba, Belize, Dominica, Grenada, Saint kitts and nevis, Saint lucia, Montserrat, Turks and caicos islands, Barbados, Bangladesh, Bermuda, Brunei darussalam, Bolivia, Ecuador, Egypt, French guiana, Guernsey, Gibraltar, Guadeloupe, Iceland, Jersey, Jordan, Cambodia, Cayman islands, Liechtenstein, Sri lanka, Luxembourg, Monaco, Macao, Martinique, Maldives, Nicaragua, Oman, Peru, Pakistan, Paraguay, Reunion, Viet nam, Uruguay.

  • Brand: Sercomm
  • Model: SW-DWS02N
  • Smart Home Protocol: Z-Wave
  • Smart Home Compatibility: Amazon Alexa
  • Connected Home Protocol: Z-Wave


Bundle New Z-Wave Door/Window Sensor, Sercomm SW-DWS02N 10 units, Motion PIR    Bundle New Z-Wave Door/Window Sensor, Sercomm SW-DWS02N 10 units, Motion PIR