Home Automation Kit

100M 2 Channel 30A High Power Relay Output AC 220V Wireless Remote Control Kit

100M 2 Channel 30A High Power Relay Output AC 220V Wireless Remote Control Kit
100M 2 Channel 30A High Power Relay Output AC 220V Wireless Remote Control Kit
100M 2 Channel 30A High Power Relay Output AC 220V Wireless Remote Control Kit
100M 2 Channel 30A High Power Relay Output AC 220V Wireless Remote Control Kit
100M 2 Channel 30A High Power Relay Output AC 220V Wireless Remote Control Kit
100M 2 Channel 30A High Power Relay Output AC 220V Wireless Remote Control Kit

100M 2 Channel 30A High Power Relay Output AC 220V Wireless Remote Control Kit    100M 2 Channel 30A High Power Relay Output AC 220V Wireless Remote Control Kit
100M 4 CH 30amps High Power Relay Output AC 220V Wireless Remote Control Gadget. 1 x Receiver: S2PU-AC220 (2 Channel / Four Control Modes). It can remote control equipments on land, water and air, such as remote control lights, sirens, locks, motors, fans, winches, blinds, linear actuators, doors, windows, electric solenoid valves, security alarm, business signs and various devices. Wireless control, easy to install. Waterproof: The receiver has waterproof case and waterproof connector, it can be installed outdoors.

Universal input: Support voltage of AC110V (100V120V), widely used in US, Canada... And voltage of AC220V (200V240V), used in UK, France..

Relay Output: This receiver is relay output, it can be used to operate both DC and AC equipments. The terminals are NO / NC (normally open / normally closed), which serves as a switch. That means you should also connect a separate power supply to equipments. High Power: Each channel can work at maximum current 30A, such as 360W/12V, 180W/6V, 270W/9V, 720W/24V, 3000W/110V, 6000W/220V. With wired control terminals: You can connect sensors, limit switches, manual switches or external devices to control the receiver.

You can turn on/ off the receiver with transmitter (remote control) from any place within a reliable distance. Wireless RF signal can pass through walls, floors, doors or windows.

With reverse power protection and over current protection. Reliable control: The receiver only works with the transmitter which use same code. One/several transmitters can control one/several receivers simultaneously. You can use two or more units in the same place. Power Supply (Operating Voltage): AC100240V (110V/120V/220V/240V). Output: Relay output (Normally open and normally closed).

Working Voltage Range of Relay: AC110240V or DC028V. Working Frequency: 315MHz / 433MHz. Control Modes: Toggle, Momentary, Latched, Momentary + Toggle. Maximum Working Current: 30A / each channel.

PCB size: 140mm x 73mm x 18mm. Case size: 192mm x 100mm x 45mm. Work with Fixed code transmitters or Learning code transmitters. With Sliding Cover: Slide up when it doesnt work (to protect the button). Slide down the button will appear.

Button Symbol: A, B, C. Operating Voltage: 12V (1 x 23A -12V battery, can be used for 12 months). Operating Frequency: 315Mhz / 433Mhz. Encoding Chip: PT2262/ PT2264/ SC2262.

Encoding Type: Fixed code (fixed code by solderingup to 6561 codes). Transmitting Distance: 100m / 300ft(theoretically).

The distance of 100m is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be exposed to some interference by other signals. Therefore, the actual distance may or may not reach 100m. If you stretches the telescopic antenna, it can have a further working range, which is twice as much as it used to be. Operating Temperature: -20 ° C to +70 ° C. Unit Size: 58mm x 39mm x 16mm. Uses: garage doors, motorcycles, car alarm products, home security products, wireless remote control products, industrial control products.

How to set up the 8-bits code of the transmitter. Open the transmitter shell, then you will see the circuit board. There are two rows pads and one row of chip feet on the back side.

The upper row of pads is L side, and the lower row of pads is H side. If solder the middle row of chip feet to the L side, it is code 1. If solder the middle row of chip feet to the H side, it is code 2.

Dont solder to any side, it is code 0. The 8-bits code order is from left to right (from D1 to D8). Here is an example, the 8-bits code in the picture is 01121101, solder as the following way. Code 0: dont solder any side, like D1 and D7.

Code 1: solder to the L side, like D2, D3, D5, D6, D8. Code 2: solder to the H side, like D4. The receiver can work with different transmitters, such as model C-2 / C-3 (100M), CWB-2 / CWB-3 (50M, waterproof), CP-2 (500M), or CB-2 / CB-3 (1000M) etc. When you set the receiver in toggle or momentary mode, it should work with two buttons transmitter, such as model C-2 (100M), CWB-2 (50M, waterproof), CP-2 (500M), or CB-2 (1000M) etc. When you set the receiver in latched mode, it should work with three buttons transmitter, such as model C-3 (100M), CWB-3 (50M, waterproof), or CB-3 (1000M) etc.

With a transmitter (such as C-2) to form a complete set, the maximum working distance can reach 100M in an open ground. The maximum working distance is a theoretical data, it shall be operated in an open ground, no barriers, no any interference. But in the practice, it will be hindered by trees, walls or other constructions, and will be interfered by other wireless signals. Therefore, the actual distance may not reach this maximum working distance. If you want to have a further working range, you can install an external antenna to the receiver, and you also can use a powerful transmitter, such as CB series transmitters. The receiver can be used to control both DC 028V and AC 110240V equipments. Notice: The receiver is relay output, not DC/AC power output.

Initial state of relay output terminals: Terminals A and B are Normally Open; Terminals A and C are Normally Closed. If you want to control a DC 12V lamp, do as following: 1 Connect the live wire of AC power supply to terminal L / + of INPUT, and connect the neutral wire of AC power supply to terminal N / - of INPUT. 2 Connect terminal B to the positive pole of DC power supply, connect terminal A to the positive pole of DC lamp, and connect the negative pole of DC lamp to the negative pole of DC power supply.

If you want to control an AC 220V lamp, do as following: 1 Connect the live wire of AC power supply to terminal L / + of INPUT, and connect the neutral wire of AC power supply to terminal N / - of INPUT. 2 Connect terminal B to the live wire of AC power supply, connect terminal A to one side of AC lamp, and connect another side of AC lamp to the neutral wire of AC power supply. If you want to use other control modes, do as following operation. Setting control mode Toggle: Only connect Jumper-2. Control mode Toggle (with transmitter C-2): Press -> On; Press again -> Off.

Press the button A of the transmitter: Turn on the relay 1 (connect A and B, disconnect A and C), the lamp 1 is on. Press the button A again: Turn off the relay 1 (disconnect A and B, connect A and C), the lamp 1 is off.

Press the button B of the transmitter: Turn on the relay 2 (connect A and B, disconnect A and C), the lamp 2 is on. Press the button B again: Turn off the relay 2 (disconnect A and B, connect A and C), the lamp 2 is off. Setting control mode Momentary: Only connect Jumper-1.

Control mode Momentary (with transmitter C-2): Press and hold -> On; Release -> Off. Press and hold the button A of the transmitter: Turn on the relay 1 (connect A and B, disconnect A and C), the lamp 1 is on. Release the button A: Turn off the relay 1 (disconnect A and B, connect A and C), the lamp 1 is off.

Press and hold the button B of the transmitter: Turn on the relay 2 (connect A and B, disconnect A and C), the lamp 2 is on. Release the button B: Turn off the relay 2 (disconnect A and B, connect A and C), the lamp 2 is off.

Setting control mode Latched: Do not connect Jumper-1 and Jumper-2. Control mode Latched (with transmitter C-3): Press -> On, other relays Off; Press another button -> Off.

Press the button C of the transmitter: Turn on the relay 1, (connect A and B, disconnect A and C), the lamp 1 is on. And turn off the relay 2 (disconnect A and B, connect A and C), the lamp 2 is off. Press the button B of the transmitter: Turn on the relay 2(connect A and B, disconnect A and C), the lamp 2 is on. And turn off the relay1 (disconnect A and B, connect A and C), the lamp 1 is off. Press the button A of the transmitter: Turn off the relays 1 and 2, the lamps are off.

Setting control mode Momentary +Toggle: connect Jumper-1& Jumper-2. Control mode Momentary (Channel 1) (with transmitter C-2): Press and hold the button A of the transmitter -> On; Release -> Off. Control mode Toggle (Channel 2) (with transmitter C-2): Press the button B of the transmitter -> On; Press the button B again -> Off. The receiver has manual control terminals, you can connect external devices, sensors, or manual switches to control the receiver. 1 Signal input: You can connect external devices (with low level output signal) to manual terminals 1 (Signal +), terminal 2 (Signal +) and terminal 3 (Signal -), then the external devices output signal can control the receiver. When the external device outputs low level signal to manual terminal 1 and terminal 3, turns on the relay 1, (connect A and B, disconnect A and C), the lamp 1 is on. When the external device stops to output signal, turns off the relay 1(disconnect A and B, connect A and C), the lamp 1 is off. When the external device outputs low level signal to manual terminal 2 and terminal 3, turns on the relay 2(connect A and B, disconnect A and C), the lamp 2 is on. When the external device stops to output signal, turns off the relay 2(connect A and B, disconnect A and C), the lamp 2 is on.

2 The manual switches: You can connect manual switches to manual terminals 1, 2 and 3, then you can use manual switches to control the receiver. When connect terminals 1 and 3, turns on the relay 1(connect A and B, disconnect A and C), the lamp 1 is on.

And when disconnect terminals 1 and 3, turns off the relay 1(disconnect A and B, connect A and C), the lamp 1 is off. When connect terminals 2 and 3, turns on the relay 2(connect A and B, disconnect A and C), the lamp 2 is on. And when disconnect terminals 2 and 3, turns off the relay 2(disconnect A and B, connect A and C), the lamp 2 is off. How to pair the transmitter to the receiver. 1 Press the learning button of receiver for 1- 2 seconds; signal LED on the receiver is on. The receiver enters into status of LEARNING.

2 Press any one button on transmitter. If signal LED flashes quickly 15 times and turns off, it means learning is successful.

3 When receiver is in the status of LEARNING, press again the learning button, signal LED turns off, learning process will be discontinued. 4 The receiver can learn several remote controls with different codes. We have learned remote control to the receiver.

If you dont want the receiver to work with the remote control, you can delete all codes of remote controls, which are stored in the receiver. Operation: Press and hold the learning button of receiver until signal LED flashes slowly; release the button, LED keeps slow flash. That means all stored codes have been deleted successfully. We are not responsible for wrong address.

The item "100M 2 Channel 30A High Power Relay Output AC 220V Wireless Remote Control Kit" is in sale since Tuesday, November 19, 2013. This item is in the category "Consumer Electronics\Surveillance & Smart Home Electronics\Other Smart Home Electronics". The seller is "carymart-usa01" and is located in shen zhen. This item can be shipped worldwide.

  • Model: 0020358
  • Compatible Technology: Insteon
  • Type: home automation
  • MPN: Does Not Apply
  • Brand: Unbranded/Generic


100M 2 Channel 30A High Power Relay Output AC 220V Wireless Remote Control Kit    100M 2 Channel 30A High Power Relay Output AC 220V Wireless Remote Control Kit